Motor Driver
-
Motor Driver
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
₹250.00 Add to cartAdjustable frequency PWM up to about 1.6 KHz
12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
Configurable push-pull or an open-drain output
The output enable pin to quickly disable all the outputs
Terminal block for power input
Reverse polarity protection on the terminal block input
Green power-good LED -
Motor Driver
A4988 Stepper Motor Driver
₹80.00 Add to cartSupply Voltage : 8-35 VDC.
Current : 1.0A (no heatsink ).
Current : 2.0A (with heat-sinking).
logic input : 3 – 5.5V . -
Motor Driver
DC Motor Speed Controller 10A
₹150.00 Add to cartSpecification:
Input supply voltage: DC 12V-40V
The maximum output power: 400W
The maximum continuous output current:8A
Static Current:0.02 A ( Standby )
PWM frequency: 13kHz
Duty Cycle adjustable: 10%-100% -
Motor Driver
DC Motor Speed Controller 3A PWM
₹95.00 Add to cartSpecifications:
Voltage range: DC6V – 28V
Current range: Within 3A
Switch function: None
Speed range: 0-100%
Dimension: 65 x 30 x 15mm
Weight: 25 g -
Motor Driver
DC Motor Speed Controller 5A PWM
₹80.00 Add to cartSpecifications:
Operating voltage: DC 4.5V- DC 35V
Output current: 0-5A
Output power: 90W (max)
Quiescent current: 7uA (standby)
PWM duty cycle: 1% -100%
PWM frequency: 20khz
Size: 30mm x 26mm x 14mm -
Motor Driver
DRV8825 Stepper Motor Driver Module with Aluminum Heat Sink
₹120.00 Add to cartOperating Voltage: 8.2V – 45V DC
Logic Voltage: 3.3V / 5V
Max Output Current: 1.5A (without heat sink), 2.2A (with cooling)
Microstepping: Up to 1/32
Interface: Step/Dir pins for control
Dimensions: 20mm × 15mm (approx.) -
Motor Driver
DRV8833 2 Channel DC Motor Driver
₹60.00 Add to cartDual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor
Operating voltage: 2.7‌‌ V to 10.8 V
Output current: 1.2 A continuous (2 A peak) per motor
Inputs are 3V- and 5V-compatible -
Motor Driver
L298N 2A Motor Driver Module
₹130.00 Add to cartInput Voltage: 3.2V to 40Vdc
Driver: L298N Dual H Bridge DC Motor Driver
Operating voltage: DC 5V – 35V
Peak Current: 2 Amps
Speed Control: PWM
Control Signal input Low voltage range: 0.3V ≤ Vin ≤ 1.5V
Control Signal input High voltage range: 2.3 ≤ Vin ≤ Vss
Enable signal input low voltage range: 0.3V ≤ Vin ≤ 1.5V (enable signal inactive)
Enable signal input high voltage range: 2.3V ≤ Vin ≤ Vss (enable signal active)
Maximum power consumption: 20W (when the temperature T = 75℃)
Onboard +5V regulated Output supply -
Motor Driver
Mini Motor Drive Shield Expansion Board L293D Module for Arduino UNO MEGA 2560
₹65.00 Add to cartInput Supply voltage (V): 4.5 ~ 25
Output Current (per channel) (mA): 600
Peak Output Current (per channel) (mA): 1.2
Switching Frequency (KHz): 5
No. of motors controlled by driver: 2 -
Motor Driver
Motor Driver TB6612FNG Module Performance Ultra Small Volume
₹180.00 Add to cartCW/CCW/short break/stop motor control modes
Built-in thermal shutdown circuit and a low voltage detecting circuit
Standby control to save power
CW/CCW/short brake/stop motor control modes
Operating Voltage(VDC): 15
Peak Current (A): 3.2
Continuous Current (A): 1.2
No. of Channels: 1 -
Motor Driver
ULN2003 Stepper Motor Driver Module
₹65.00 Add to cart7 high-voltage and high current Darlington pairs
50V and 500mA for each pair
Input pins triggering voltage: 5V
All seven Output pins can be connected to gather to drive loads up to 3.5A
Low cost and Reliable
